This is a low noise and distortion pre-amplifier and tone control circuit in one module. Using a special IC TDA1524A, this simple circuit is easy to build and will drive most of power amplifier.
Schematic diagram:
Pre-Amp + Tone Control Components List:
Resistors: R1, R2__________________ 220R R3, R4__________________ 4K7 R5______________________ 2K2 R6______________________ 1K Capacitors: C1, 2, 7, 8, 17_________ 10 uF ecap C3, 4___________________ 47 nF C5, 6___________________ 15 nF C9______________________ 220 nF poly C10_____________________ 100 uF 25V C11, 12, 13, 14, 16_____ 100 nF C15_____________________ 1000 uF 35V C18, 19_________________ 10 nF Misc.: IC1_____________________ TDA 1524A IC2_____________________ LM 7812 P1______________________ 50k linear switch pot P2, 3, 4________________ 50k linear pot X1, 2, 3, 4_____________ RCA jack D1______________________ Diode 1N4004 L1______________________ Red LED
Circuit Works:
All signal processing is done within the TDA1524A by voltage controlled amplifiers and voltage controlled filters. The IC provides a fixed voltage (~ 3.8V DC) at pin 17, and this is used by all the variable resistors to provide an adjustable DC voltage to the appropriate control pins.
Current sensing is used to provide a flat response when R5 is connected to pin 17, and a loudness contour when disconnected. 100 nF capacitors are used on each pot to decouple any AC signals from the control inputs. 10 uF capacitors are used to couple both input and output audio signals whilst blocking DC. R1 and R2, are to ensure stability with capacitive loads. R3 and R4 make sure there are no DC spikes at the output sockets if the load is switched. C3 and C4 control the loudness contour. C5 and C6 control the treble turn-over frequency. C18 and C19 have been added to roll off the gain above 70 kHz. Low volume settings coupled with treble boost was causing HF instability in some instances. This should no longer be a problem.
C15, 16, 17 provide power supply filtering. D1 provides protection in case of incorrect supply polarity. The LED is a power on indicator and may be omitted if not required, or preferably mounted on the enclosure. If you are not using a switch pot, you can connect an external switch across the P1 switch pins, or connect a wire link there and switch the power supply.
The power supply is critical to the noise performance of the pre-amp. An on board regulator is provided to reduce mains hum. If you wish to use it with a car or other 12V battery, then you should omit the 7812 regulator, and place a wire link between the regulator input and output pin positions on the PC board. Do not short to earth! This will be necessary because the regulator must have an input voltage at least 2-3V greater than it”s output, for it to maintain regulation. However the regulator will not be necessary with a battery supply.
If using a plug pack, it”s output voltage should be 15 to 18V DC. Because most plug packs have poor regulation, one rated at 12V DC will often be around 15V when lightly loaded. The current drain of the pre-amp is less than 50 mA, so many 12 V unregulated supplies may be adequate if you have one. Replace D1 with a wire link if necessary, making sure you have the supply polarity correct!
If you are using a 15-20V supply for your power amplifier, you can use that as your pre-amp supply as well. Make sure you test the voltage first in all cases.
Download the Pre-Amp + Tone Control Circuit Manual in PDF:
Download TDA1524A Stereo-tone/volume control circuit:
This is the circuit diagram of power amplifier 45W using power uPC 1230 as the…
The Horn Circuit This is a basic circuit of car horn and lamp flasher that…
This is the circuit diagram of drinking water alarm based a small water sensor by…
Here is the 200W MOSFET amplifier powered based on four piece of IRFP250N, they are…
This is the 300W RMS stereo power amplifier circuit project. This amplifier is based four…
This is an active stereo tone control circuit using very well known op-amp IC of…
View Comments
good diagram....
hi there
nice design . how about it's pcb ?
greetings .
The is a small chance that the circuit will be damaged due to over current, the preamplifier only consumes 50mA and batteries don't have current limiting characteristics . To make sure its ok, a "Choke Inductor" is in series to the power supply before going the voltage regulator, 7812 does NOT have short circuit and current limiting characteristics( Especially when you are using a 12v Automotive battery). And be sure that you included a fuse when using an automotive battery as power supply. When a short circuit was occurred, the current will go up to 200AMPERES!!, so better think about it.
Hello Mave,
I think the requlator IC LM78xx has current limit of 1A to 1.5A.
http://www.instructables.com/id/Increasing-current-on-78xx-series-regulators/
CMIIW
i use 17v(5 amperes) for this amp. is it ok?
yes, it should be ok...
is it possible to get the completed circuit board in eagle?
i will like to thank u all for providing as good circuit diagrams and i will like to know and learn more about your circuit diagrams but i still need a diagram of an amplifier and also pre-amp with tone control circuit diagrams thank u and have a nice day
the circuit is okay.but i still need a diagram of stk amplifier
when it comes to car audio, Pionner brand and Alpine seems to be the leader specially on car stereo and players.-:
i want to learn more about pre amp ,amplifiers , its component and power supplys
operation concerning mid , treble and bass (to operate mid alone , treble alone, bass alone or all in one)with the same power supply